Telephone _ James Duff, Inc.

865.938.6696

M-F 10-6 EST

You are here: Home > Bronco II 1984-1990 > Accessories Exterior
Sort By:
Page of 3
Ford Bronco II Skid Plate
Duff Tuff Skid Plate, Ford Bronco II, 83-92 Ranger, 91-94 Explorer
Our Price: $159.95

Back by popular demand! Our 1/8" aluminum Duff Tuff Skid Plate gives a finished look to your front end while adding extra protection for your radiator. Backed with a steel frame for strength, it's an easy install, bolting to the frame sway bar mounts and the front crossmember.  Shown on our '84 Bronco II with Plate Winch Bumper. When fitting to the Explorer chassis, locating and drilling of new holes in vehicle frame or skid plate may be required. Winch, roller fairlead, light bracket, and KC Hilites Slim Lights, if desired, must be purchased from other vendors.
Gas Can Rack Carrier Duff Bumpers 1966-77 Early Classic EB Bronco BII Bronco II Ford
Gas Can Carrier for Duff Carrier Bumpers
Our Price: $299.95

Add the optional, driver’s side mounted, 5 gallon can carrier to your Duff Carrier Bumper. Made with the same stout material and features as our tire carrier bumper. Fits most plastic and metal 5 gallon “Gerry” cans. Can is removable through the back or front. (Not through cooler carrier like some.) Includes Hinge and Cam Latch with Brass Oilite Bushings. Cooler rack option available at additional charge (#4982B). (NOTE: Cooler rack cannot be added to Bronco II bumper due to angle of lift gate.)
Prerunner Rear Receiver Bumper Bronco II Ranger
Prerunner Rear Receiver Bumper, Bronco II & 83-97 Ranger
Our Price: $359.95

Our Rear Pre-Runner Bumpers are constructed of 2" x .120 wall tubing, features a gusseted and reinforced 2" receiver and is quick and easy to install with included hardware. Fits 1984-90 Bronco II and 1983-1997 Ranger (frame adapter mounts included when Ranger application is specified).
All bumpers ship bare and must be final prepped and finished to your liking. We will contact you with shipping rates.
Pre-Runner Step Bumper  Bronco II 1983-97 Ford B2 Ranger Tow Ball
Pre-Runner Step Bumper, Bronco II & 1983-97 Ranger
Our Price: $369.95

Our Pre-Runner Ball Mount/Step Bumper is made of 2" .120 wall steel tube with a 3/8" thick center section for serious strength to mount a 7/8" shank tow ball. Fits 1984-90 Bronco II and 1983-1997 Ranger (frame adapter mounts included when Ranger application is specified). All bumpers ship bare and must be final prepped and finished to your liking. We will contact you with shipping rates.
Ft. Prerunner Bumper 1983-88 Bronco II & Ford Ranger Tube Pre-Runner
Ft. Prerunner Bumper 1983-88 Bronco II & Ranger
Our Price: $379.95

The basic first generation prerunner bumper is virtually unchanged from our previous design as it is still made from 2” and 1.5” diameter .120 (1/8”) wall steel tubing with dual light tabs on the front center hoop, tabs to mount license plate and reinforcements to strengthen the stock frame. The sides of the bumper now feature a larger end cap on the tubes. All bumpers ship bare and must be final prepped and finished to your liking. We will contact you with shipping rates.
Ft Pre-runner Bumper 1989-90 Bronco II B2 BII 1989-92 Ford Ranger & 91-94 Explorer RBV Pre Runner Tube
Ft Pre-runner Bumper 1989-90 BII, 89-92 Ranger & 91-94 Explorer
Our Price: $399.95

Virtually unchanged from our previous design as it is still made from 2” and 1.5” diameter .120 (1/8”) wall steel tubing with dual light tabs on the front center hoop, tabs to mount license plate and reinforcements to strengthen the stock frame. The sides of the bumper now feature a larger end cap on the tubes. Includes our Dufflector Ends to be either bolted or welded on with included bolts (not attached to keep shipping costs down). This gives the bumper a finished look and hides the unsightly body lines left behind when the factory plastic is removed. All bumpers ship bare and must be final prepped and finished to your liking. We will contact you with shipping rates.
Winch Plate Bumper, 83-88 Bronco II & Ford Ranger First Generation
Winch Plate Bumper, 83-88 Bronco II & Ranger
Our Price: $575.00

Our plate steel winch bumper is designed for up to a 9500 pound winch. Designed to maximize your approach angle yet with the lowest possible winch mount height for maximum air flow to the radiator. Constructed of a combination of 3/16” and 1/4” plate for maximum strength without too much weight. 1/4” plate wrap around protection for lower fenders. Laser cut openings for jacking points and attachment points for shackles or tow bar. Laser etched "JD" logos on chiseled end plates. Same model fits with or without body lift. Shown on our '84 with a 1" body lift.

Now also available with a center hoop option. It has two light tabs spaced for a pair of round lights or up to a 13" light bar. Please note that having us weld on the hoop adds about double to the cost of freight, depending on where you are located. As an alternative, we offer the DIY option of the hoop separately.

All bumpers ship bare and must be final prepped and finished to your liking. We will contact you with shipping rates.


Front Pre-Runner Winch Bumper, 1989-90 Ford BII Bronco II B2, 1989-92 Ranger, 1991-94 Explorer Tube Pre Runner
Front Pre-Runner Winch Bumper, 1989-90 BII, 89-92 Ranger, 91-94 Explorer
Our Price: $669.95

Like our previous design, great care was taken to maximize approach angles and body protection while minimizing airflow blockage. Made from 2” and 1.5” diameter .120 (1/8”) wall steel tubing with dual light tabs on the front center hoop. Angled license plate mounting under the winch plate designed to handle up to a 9500# winch. Includes reinforcements to strengthen the stock frame. The sides of the bumper now feature a larger end cap on the tubes. Includes our Dufflector Ends to be either welded or bolted on (with included bolts, not attached to keep shipping costs down). This gives the bumper a finished look and hides the unsightly body lines left behind when the factory plastic is removed.
All bumpers ship bare and must be final prepped and finished to your liking. We will contact you with shipping rates.
bronco 2 ii plate carrier receiver bumper can jack
Bronco II Rear Plate Bumper with Tire Carrier and Optional Can Rack
Our Price: $699.99

Stock tire carriers just don't stand up to the weight of an oversize tire. The extra weight can cause the factory mounts on the quarter panel to tear. So, we designed a carrier system utilizing our proven 2” receiver plate bumper. The rear plate bumper is made of 3/16” steel with 1/4” end plates, frame mounts, and gussets. We add strength in all the important spots. It will carry up to a 35” tire while also providing a location for a Hi-Lift Jack. The spare tire mounts to the carrier with pressed in wheel studs and included lug nuts (you can also use standard locking lug nuts for added security). The jack sits on a steel base and is secured with a T-handle.

Access to your liftgate is quick and easy thanks to our simple but effective cam-latch design. The hinge pivots feature oil impregnated brass bushings for long life. A drop pin automatically holds the carrier open so there is no fear of it swinging in either direction.

The optional carrier basket (#4981, sold separately) is set up for a 5 gallon “Gerry” can, but readily accepts water, antifreeze jugs or a trash can! Mounting hardware is included. Ships bare so that you can finish to your liking. We do not currently sell the cooler rack addition for Bronco II, it will bolt on but the hatch will not open due to clearance.

Consider adding #4934, our winch plate bumper for the front of your Bronco II.

This bumper is designed for the 84-88 Bronco II only.

We will contact you with shipping costs.

Pre-runner Winch Bumper 1983-88 Bronco II & Ford Ranger B2 BII Tube Prerunner Pre Runner
Pre-runner Winch Bumper 1983-88 Bronco II & Ranger
Our Price: $729.95

The first generation front Pre-Runner winch bumper is virtually unchanged from our previous design. Great care was taken to maximize approach angles and body protection while minimizing airflow blockage. Made from 2” and 1.5” diameter .120 (1/8”) wall steel tubing with dual light tabs on the front center hoop. Angled license plate mounting under the winch plate designed to handle up to a 9500# winch. Includes reinforcements to strengthen the stock frame. The sides of the bumper now feature a larger end cap on the tubes.
All bumpers ship bare and must be final prepped and finished to your liking. We will contact you with shipping rates.