|
|
|
|
|
|
Bolt Set W/Nuts for Chrome Bumper, 1966-77 Bronco
|
|
|
Replace your old rusty bumper bolts with this new STAINLESS bolt set!
(NOTE: This set does not include the carriage bolt head bolts for the square punched holes in the middle of the bumper where the bumperettes mounted.)
|
|
|
|
|
|
|
|
|
|
Reproduction Chrome Bumper, Ft or Rear, 1966-77 Bronco
|
|
|
Reproduction original style chrome bumper fits front or rear, 66-77 Ford Broncos. For new hardware, we recommend our stainless steel bumper bolt kit, #4967. Note that all packages over 48" are now assessed a $12.00 added handling fee by UPS.
|
|
|
|
|
|
|
|
|
|
Duff Tuff Skid Plate, Ford Bronco II, 83-92 Ranger, 91-94 Explorer
|
|
|
Back by popular demand! Our 1/8" aluminum Duff Tuff Skid Plate gives a finished look to your front end while adding extra protection for your radiator. Backed with a steel frame for strength, it's an easy install, bolting to the frame sway bar mounts and the front crossmember. Shown on our '84 Bronco II with Plate Winch Bumper. When fitting to the Explorer chassis, locating and drilling of new holes in vehicle frame or skid plate may be required. Winch, roller fairlead, light bracket, and KC Hilites Slim Lights, if desired, must be purchased from other vendors.
|
|
|
|
|
|
|
|
|
|
Receiver Hitch, 1966-77 Bronco
|
|
|
This 2" receiver is a Class II hitch, 3500 lb. capacity, 300 lb. tongue weight. Proven design we've been selling for over 20 years slips into the ends of the frame, mounts using original bolt holes, NO drilling required. Can be used front or rear. Fits 1966-77, 1976-77 require slight modification to the gas tank skid plate. Matte Black Powder Coated for longevity.
DOES NOT INCLUDE RECEIVER INSERT OR PIN. Note: Due to frame mount changes the #4905 will not work with our Pre-Runner bumpers.
|
|
|
|
|
|
|
|
|
|
Gas Can Carrier for Duff Carrier Bumpers
|
|
|
Add the optional, driver’s side mounted, 5 gallon can carrier to your Duff Carrier Bumper. Made with the same stout material and features as our tire carrier bumper. Fits most plastic and metal 5 gallon “Gerry” cans. Can is removable through the back or front. (Not through cooler carrier like some.) Includes Hinge and Cam Latch with Brass Oilite Bushings. Cooler rack option available at additional charge (#4982B). (NOTE: Cooler rack cannot be added to Bronco II bumper due to angle of lift gate.)
|
|
|
|
|
|
|
|
|
|
Pre-Runner Receiver Bumper, 1966-77 Bronco
|
|
|
Our Rear Pre-Runner Bumper is constructed of 2" x .120 wall tubing, features a gusseted and reinforced 2" receiver and is quick and easy to install using your original frame bolts. Available in stock or body lifted version to help offset the gap left when adding a 1-2" body lift. If you have a body lift, please note it in the comments section when you order (1" or 2" body lift offset available). All bumpers ship bare and must be final prepped and finished to your liking. We will contact you with shipping rates.
|
|
|
|
|
|
|
|
|
|
Prerunner Rear Receiver Bumper, Bronco II & 83-97 Ranger
|
|
|
Our Rear Pre-Runner Bumpers are constructed of 2" x .120 wall tubing, features a gusseted and reinforced 2" receiver and is quick and easy to install with included hardware. Fits 1984-90 Bronco II and 1983-1997 Ranger (frame adapter mounts included when Ranger application is specified).
All bumpers ship bare and must be final prepped and finished to your liking. We will contact you with shipping rates.
|
|
|
|
|
|
|
|
|
|
Pre-Runner Step Bumper, Bronco II & 1983-97 Ranger
|
|
|
Our Pre-Runner Ball Mount/Step Bumper is made of 2" .120 wall steel tube with a 3/8" thick center section for serious strength to mount a 7/8" shank tow ball. Fits 1984-90 Bronco II and 1983-1997 Ranger (frame adapter mounts included when Ranger application is specified). All bumpers ship bare and must be final prepped and finished to your liking. We will contact you with shipping rates.
|
|
|
|
|
|
|
|
|
|
Pre-Runner Bumper, 1966-77 Early Bronco
|
|
|
Easy to install using your original frame bolt holes
•2” diameter .120 (1/8”) wall steel tubing
•Reinforced steel plate Dufflector Ends protect fenders
•Sits close to the body to maximize approach & departure angles
•Standard dual light tabs on the front center hoop
will fit up to a 9” light mounted up or down
•All bumpers ship bare and must be final prepped and finished to your liking
One version for both body lifted or not. Shown on Silver with 2" Body Lift, on Teal Green Bronco stock.
We will contact you with shipping rates.
|
|
|
|
|
|
|
|
|
|
Ft Pre-runner Bumper 1989-90 BII, 89-92 Ranger & 91-94 Explorer
|
|
|
Virtually unchanged from our previous design as it is still made from 2” and 1.5” diameter .120 (1/8”) wall steel tubing with dual light tabs on the front center hoop, tabs to mount license plate and reinforcements to strengthen the stock frame. The sides of the bumper now feature a larger end cap on the tubes. Includes our Dufflector Ends to be either bolted or welded on with included bolts (not attached to keep shipping costs down). This gives the bumper a finished look and hides the unsightly body lines left behind when the factory plastic is removed. All bumpers ship bare and must be final prepped and finished to your liking. We will contact you with shipping rates.
|
|
|
|
